Back to blog

DISINFICTING YOUR DIVE EQUIPMENT

Image to render

Disinfecting your scuba diving equipment

As we start to see people return to scuba diving around the world, we're sharing the following information to help you learn more about how to safely clean and store your scuba diving equipment between uses. 

This artcile mentions specific products that are available, thesre are products that we have tested and know to be safe to use with our products. All products are listed at the end of this article, however similar products with the same disinfecting properties are available around the world.

REGULATORS

Warning do not use based disinfectants or disinfectants known to be corrosive, as these can prematurely age or corrode the equipment being used.

LOW RISK ENVIRONMENT    

If there is a low risk of bacterial and/or viral transmission (infection from mould and fungal growth or saliva bacteria/viral transmission), then after each use wash with warm tap water and general household dish soap for several minutes to remove any visible dirt and staining. A soft sponge can also be used, taking great care around any rubber valves so not to dislodge or damage them. Ensure that all traces of soap are rinsed and flushed away with clean potable cold water. 

Once rinsed, the regulator should be purged to remove excess water and then dried and stored in a clean dry area to reduce the risk of bacteria growth.This would normally be sufficiently clean for immediate reuse if required.  

HIGH RISK ENVIRONMENT

If there is a high risk of bacterial and/or viral transmission (infection from mould and fungal growth or saliva bacteria/viral transmission) from shared daily use between trainees after each training session, then disinfection can be achieved by the use of Chemgene HLD4L breathing apparatus surface disinfectant solution. 

The regulator should first be washed, rinsed and purged as above. The regulator is placed in a solution of 50 parts water to 1 part HLD4L (50:1) laboratory non-fragranced anti-bacterial solution and slightly agitated initially. Leave to soak for 20 minutes. The disinfectant should be rinsed off the regulator with running potable cold

MEDIUM RISK ENVIRONMENT

If there is a medium risk of bacterial and/or viral transmission (infection from mould and fungal growth or saliva bacteria/viral transmission) from shared daily use between trainees after each training session, then disinfection can be achieved by using Chemgene HLD4L breathing apparatus surface disinfectant solution. 

The unit should first be washed, rinsed and purged as above. The regulator is then placed in a solution of 100 parts water to 1 part HLD4L (100:1) laboratory non-fragranced anti-bacterial solution and slightly agitated initially. Leave to soak for 20 minutes. The disinfectant should be rinsed off the regulator with running potable cold water and then purged while the mouthpiece is facing up and then down to ensure any residual water is purged from inside the regulator. The unit is then ready to be reused - or can be dried and stored.

DRYING AND STORAGE 

To dry the unit ready for storage, the regulator should be purged with the breathing gas on while the mouthpiece is facing upwards and then downwards. This is to ensure that all residual water has been drained from inside the regulator during the cleaning process. 

It is also recommended that the unit be disinfected periodically to further reduce the risk of bacterial growth.

MASKS, FINS AND BCDS

We recommend SeptiOne Matériel to disinfect your fins, mask and BCD. 

Its properties are bactericidal, fungicidal, virucidal and an algicide (AFNOR standards). It is biodegradable. 

SeptiOne Matériel is prepared by dilution to 2% in fresh water. The equipment can then be disinfected by soaking it for 10 minutes in a volume of water to which an appropriate volume of product has been added beforehand. This soaking must be followed by a careful rinsing. 

PRODUCT NAMES AND LINKS 

A useful resource is the EPA's N-List which names other products that are effective against Coronavirus (remember to avoid the bleach based products)

  • Please note that we cannot advise on products not listed here, however the links above should give you an opportunity to locate similar products in your own regions.
  • This advice on this page does not replace common sense and adhering to guidelines and restrictions in your region.
  • This advice can only reduce, not remove, the chance of viral transmission from dive equipment

Image to render

GRAPHENE TECHNOLOGY

Where cool design meets state of the art technology, the Apeks ThermiQ Carbon Core sets new standards in base layer thermal protection. 
See more
Image to render

APEKS TAKES THE PLUNGE WITH NEW SOLAR INSTALLATION

Blackburn-based kit manufacturer Apeks, part of the global dive and swim company Aqua Lung International, has continued with its switch to green by installing 400 solar panels on the roof of its purpose built factory in the UK.  

See more
Image to render

THE LOST REG

In 2016, a diver had to ditch his rig during a drift dive in Norway. Three years later he found it again. 
See more
Image to render

ZERO WASTE TO MANDFILL ACHIEVEMENT!

100% of general waste from the business is now turned into biofuel, which goes on to provide fuel for heating and hot water in other industries. 

See more